Abaei, M. Morphological Investigation of Al-Cu-Fe Quasi-Crystalline Thin Film on Ti-6Al-4V Alloy [Volume 21, Issue 1, 2024, Pages 9-14]
Afsari, O, Study on Vibration of Middle Leg in The MIDREX Shaft Furnace [Volume 21, Issue 1, 2024, Pages 51-60]
Aghebatkheiri, F. Isothermal Kinetic Analysis of Dissolution of The Retained Delta Ferrite in AISI 304 Stainless Steel During Homogenization [Volume 21, Issue 1, 2024, Pages 1-8]
Akhondizadeh, M. Study on Vibration of Middle Leg in The MIDREX Shaft Furnace [Volume 21, Issue 1, 2024, Pages 51-60]
Allahdadi, M. Enhancing the Production Rate of Mobarakeh MIDREX Direct Reduction Mega Module Unit Using Numerical Simulation and Geometric Parameter Study of its Ejector Stack [Volume 21, Issue 1, 2024, Pages 75-84]
Amini Najafabadi, R. Production of Bio-Carbon Materials from Animal Manure That Can Be Used in Iron Reduction [Volume 21, Issue 2, 2024, Pages 73-78]
Arzani, S. Investigation of the Effect of SiO2 Nanoparticles on Corrosion-Wear-Impact Resistance, and Bending Strength of Acrylic Coating Applied To Steel Substrate [Volume 21, Issue 2, 2024, Pages 1-10]
Ashrafi, H. Microstructure and Corrosion Behavior of Friction Stir-Welded DP600 Steel [Volume 21, Issue 1, 2024, Pages 15-23]
B
Bahaadini, R. Study on Vibration of Middle Leg in The MIDREX Shaft Furnace [Volume 21, Issue 1, 2024, Pages 51-60]
Bakhshandeh, A. R. Tribological Behavior of Weld Zone in TIG-Welded AISI410 Martensitic Stainless Steel [Volume 21, Issue 2, 2024, Pages 62-72]
Balooch, A. Utilizing Gum Commiphora Mukul as Organic Binders to Replace Bentonite in Iron Ore Pelletizing [Volume 21, Issue 2, 2024, Pages 39-46]
Basiriani, B. Enhancing the Production Rate of Mobarakeh MIDREX Direct Reduction Mega Module Unit Using Numerical Simulation and Geometric Parameter Study of its Ejector Stack [Volume 21, Issue 1, 2024, Pages 75-84]
Beigi, M. Evaluation of Mechanical Properties and Corrosion Resistance in Welded Stainless Steel 321H: Influence of Buttering Techniques [Volume 21, Issue 2, 2024, Pages 79-92]
D
Darbandi, M. Enhancing the Production Rate of Mobarakeh MIDREX Direct Reduction Mega Module Unit Using Numerical Simulation and Geometric Parameter Study of its Ejector Stack [Volume 21, Issue 1, 2024, Pages 75-84]
E
Ebrahimi, َA. R. Effects of CeO2 Flux and Shielding Gas In A-TIG Welding on The Microstructure, Corrosion and Passive Film of Super Duplex Phase Stainless Steel 2507 [Volume 21, Issue 1, 2024, Pages 61-74]
Ebrahimi, R. A Novel Approach for Estimating Fatigue Behavior of Stainless Steel 304 Using Tensile Test Data [Volume 21, Issue 1, 2024, Pages 45-50]
Elmi hosseini, R. A Critical Review on Dissimilar Welding of Stainless Steels To Titanium Alloys: Technology and Metallurgy [Volume 21, Issue 2, 2024, Pages 93-107]
Eshraghi, M. J. Morphological Investigation of Al-Cu-Fe Quasi-Crystalline Thin Film on Ti-6Al-4V Alloy [Volume 21, Issue 1, 2024, Pages 9-14]
F
Farhadi, P. Improving the Steel Household Appliances Production Through Simulation and Gray Proximity Indexed Value [Volume 21, Issue 2, 2024, Pages 47-61]
Farrokhi, A. Enhancing Atmospheric Corrosion Resistance of Shot-Peened A36 Steel in Humid Environments: The Impact of Carbon Monoxide and Surface Treatments [Volume 21, Issue 2, 2024, Pages 21-30]
Farvizi, M. Morphological Investigation of Al-Cu-Fe Quasi-Crystalline Thin Film on Ti-6Al-4V Alloy [Volume 21, Issue 1, 2024, Pages 9-14]
Fazeli, M. Enhancing the Production Rate of Mobarakeh MIDREX Direct Reduction Mega Module Unit Using Numerical Simulation and Geometric Parameter Study of its Ejector Stack [Volume 21, Issue 1, 2024, Pages 75-84]
Foroughi, V. A Critical Review on Dissimilar Welding of Stainless Steels To Titanium Alloys: Technology and Metallurgy [Volume 21, Issue 2, 2024, Pages 93-107]
G
Ghaderi, S. Tribological Behavior of Weld Zone in TIG-Welded AISI410 Martensitic Stainless Steel [Volume 21, Issue 2, 2024, Pages 62-72]
Gharibi, M. Improving the Steel Household Appliances Production Through Simulation and Gray Proximity Indexed Value [Volume 21, Issue 2, 2024, Pages 47-61]
Guliani, M. Effects of CeO2 Flux and Shielding Gas In A-TIG Welding on The Microstructure, Corrosion and Passive Film of Super Duplex Phase Stainless Steel 2507 [Volume 21, Issue 1, 2024, Pages 61-74]
H
Hasani, S. Isothermal Kinetic Analysis of Dissolution of The Retained Delta Ferrite in AISI 304 Stainless Steel During Homogenization [Volume 21, Issue 1, 2024, Pages 1-8]
Hasanpoor, J. Utilizing Gum Commiphora Mukul as Organic Binders to Replace Bentonite in Iron Ore Pelletizing [Volume 21, Issue 2, 2024, Pages 39-46]
Hosseinian, S. M. Enhancing the Production Rate of Mobarakeh MIDREX Direct Reduction Mega Module Unit Using Numerical Simulation and Geometric Parameter Study of its Ejector Stack [Volume 21, Issue 1, 2024, Pages 75-84]
Hossienpour, M. Investigation of Nitriding Effect on Cutting Vibration of Indexable End Mill During the Straight Groove [Volume 21, Issue 2, 2024, Pages 11-20]
I
Inanloo, E. Investigation of Nitriding Effect on Cutting Vibration of Indexable End Mill During the Straight Groove [Volume 21, Issue 2, 2024, Pages 11-20]
K
Khosravifard, A. Evaluation of Mechanical Properties and Corrosion Resistance in Welded Stainless Steel 321H: Influence of Buttering Techniques [Volume 21, Issue 2, 2024, Pages 79-92]
Koohestani, H. Utilizing Gum Commiphora Mukul as Organic Binders to Replace Bentonite in Iron Ore Pelletizing [Volume 21, Issue 2, 2024, Pages 39-46]
M
Mahdikhani, B. Investigation of Nitriding Effect on Cutting Vibration of Indexable End Mill During the Straight Groove [Volume 21, Issue 2, 2024, Pages 11-20]
Maleki, Z. Using Recycled Machining Chips and Reduced Graphene Oxide in Spot Welding of Galvanized Sheets to Improve Hardness and Corrosion Resistance [Volume 21, Issue 1, 2024, Pages 24-32]
Mashreghi, A. R. Isothermal Kinetic Analysis of Dissolution of The Retained Delta Ferrite in AISI 304 Stainless Steel During Homogenization [Volume 21, Issue 1, 2024, Pages 1-8]
Mehrabi Gohari, E. Evaluation of Mechanical Properties of Welding ST-37 Steel Structures With Two Types of Welding Processes FCAW and SMAW [Volume 21, Issue 1, 2024, Pages 33-44]
Mohammadi, M. Microstructure and Corrosion Behavior of Friction Stir-Welded DP600 Steel [Volume 21, Issue 1, 2024, Pages 15-23]
Mohsenzadeh, F. M. Aspen HYSYS Simulation of Reformer and Heat Recovery System [Volume 21, Issue 2, 2024, Pages 31-38]
Monazami Tehrani, G. Aspen HYSYS Simulation of Reformer and Heat Recovery System [Volume 21, Issue 2, 2024, Pages 31-38]
Mostaan, H. Tribological Behavior of Weld Zone in TIG-Welded AISI410 Martensitic Stainless Steel [Volume 21, Issue 2, 2024, Pages 62-72]
N
Namvarian, R. A Novel Approach for Estimating Fatigue Behavior of Stainless Steel 304 Using Tensile Test Data [Volume 21, Issue 1, 2024, Pages 45-50]
Norouzi Palangani, F. Using Recycled Machining Chips and Reduced Graphene Oxide in Spot Welding of Galvanized Sheets to Improve Hardness and Corrosion Resistance [Volume 21, Issue 1, 2024, Pages 24-32]
P
Pakzaman, H. RezaInvestigation of the Effect of SiO2 Nanoparticles on Corrosion-Wear-Impact Resistance, and Bending Strength of Acrylic Coating Applied To Steel Substrate [Volume 21, Issue 2, 2024, Pages 1-10]
Parsai Kia, َA. Investigation of Hydrate Formation Conditions of Simulated Flue Gas in TBAB Solution with Potential Application in CO2 Capture in Steel Industry [Volume 21, Issue 1, 2024, Pages 85-89]
Payab, A. Aspen HYSYS Simulation of Reformer and Heat Recovery System [Volume 21, Issue 2, 2024, Pages 31-38]
Payab, H. Aspen HYSYS Simulation of Reformer and Heat Recovery System [Volume 21, Issue 2, 2024, Pages 31-38]
Poudinehei, R. Using Recycled Machining Chips and Reduced Graphene Oxide in Spot Welding of Galvanized Sheets to Improve Hardness and Corrosion Resistance [Volume 21, Issue 1, 2024, Pages 24-32]
R
Rabiei, A. Production of Bio-Carbon Materials from Animal Manure That Can Be Used in Iron Reduction [Volume 21, Issue 2, 2024, Pages 73-78]
Rabiezadeh, A. Evaluation of Mechanical Properties and Corrosion Resistance in Welded Stainless Steel 321H: Influence of Buttering Techniques [Volume 21, Issue 2, 2024, Pages 79-92]
Rafiei, M. Tribological Behavior of Weld Zone in TIG-Welded AISI410 Martensitic Stainless Steel [Volume 21, Issue 2, 2024, Pages 62-72]
Rahi, A. Investigation of Nitriding Effect on Cutting Vibration of Indexable End Mill During the Straight Groove [Volume 21, Issue 2, 2024, Pages 11-20]
Rahimipour, M. R. Morphological Investigation of Al-Cu-Fe Quasi-Crystalline Thin Film on Ti-6Al-4V Alloy [Volume 21, Issue 1, 2024, Pages 9-14]
Rashidi, D. Enhancing the Production Rate of Mobarakeh MIDREX Direct Reduction Mega Module Unit Using Numerical Simulation and Geometric Parameter Study of its Ejector Stack [Volume 21, Issue 1, 2024, Pages 75-84]
Reihanian, M. A Novel Approach for Estimating Fatigue Behavior of Stainless Steel 304 Using Tensile Test Data [Volume 21, Issue 1, 2024, Pages 45-50]
S
Sani, R. Evaluation of Mechanical Properties and Corrosion Resistance in Welded Stainless Steel 321H: Influence of Buttering Techniques [Volume 21, Issue 2, 2024, Pages 79-92]
Sedehi, S. M. R. Using Recycled Machining Chips and Reduced Graphene Oxide in Spot Welding of Galvanized Sheets to Improve Hardness and Corrosion Resistance [Volume 21, Issue 1, 2024, Pages 24-32]
Seyedi, S. H. Improving the Steel Household Appliances Production Through Simulation and Gray Proximity Indexed Value [Volume 21, Issue 2, 2024, Pages 47-61]
Seyedi, S. M. Improving the Steel Household Appliances Production Through Simulation and Gray Proximity Indexed Value [Volume 21, Issue 2, 2024, Pages 47-61]
Shanaghi, A. Enhancing Atmospheric Corrosion Resistance of Shot-Peened A36 Steel in Humid Environments: The Impact of Carbon Monoxide and Surface Treatments [Volume 21, Issue 2, 2024, Pages 21-30]
Y
Yazdi, S. H. Using Recycled Machining Chips and Reduced Graphene Oxide in Spot Welding of Galvanized Sheets to Improve Hardness and Corrosion Resistance [Volume 21, Issue 1, 2024, Pages 24-32]
Yousefi, S. Investigation of Hydrate Formation Conditions of Simulated Flue Gas in TBAB Solution with Potential Application in CO2 Capture in Steel Industry [Volume 21, Issue 1, 2024, Pages 85-89]
