[1] Deng Y.G, Li Y, Di H, Misra R.D.K, Effect of heating rate during continuous annealing on microstructure and mechanical properties of high-strength dual-phase steel. J Mater Eng Perform. 2019; 28: 4556–64.
[2] Tian C, Kusche C.F, Medina A, Lee S, Wollenweber M.A, Pippan R, et al. Understanding the damage initiation and growth mechanisms of two DP800 dual phase grades. Mater Des. 2024; 238: 112630.
[3] Ashrafi H, Shamanian M, Emadi R, Saeidi N, Correlation of tensile properties and strain hardening behavior with martensite volume fraction in dual-phase steels. Trans Indian Inst Met. 2017; 70: 1575–84.
[4] Deng Y.G, Yang Y.P, Fine-grained dual-phase steels fabricated via cold-rolling ferrite-martensite structure and subsequent intercritical annealing, J Mater Res Technol. 2023; 27: 3881-6.
[5] Ashrafi H, Shamanian M, Emadi R, Sarmadi M.A, Comparison of microstructure and tensile properties of dual phase steel welded using friction stir welding and gas tungsten arc welding. Steel Res Int. 2018; 89: 1700427.
[6] Jia Q, Guo W, Li W, Peng P, Zhu Y, Zou G, et al. Experimental and numerical study on local mechanical properties and failure analysis of laser welded DP980 steels, Mater Sci Eng A. 2017; 680: 378–87.
[7] Bandyopadhyay K, Panda S.K, Saha P, Investigations into the influence of weld zone on formability of fiber laser-welded advanced high strength steel, J Mater Eng Perform. 2014; 23: 1465–79.
[8] Gibson B.T, Lammlein D.H, Prater T.J, Longhurst W.R, Cox C.D, Ballun M.C, et al. Friction stir welding: process, automation, and control. J Manuf Process. 2014; 16: 56-73.
[9] Wu Q, Li M, Guo Y, Shan J, Wang H, Chang Y, Microstructural evolution and mechanical properties of friction stir welded 12Cr-ODS steel, Nucl Mater Energy. 2020; 25: 100804.
[10] Miles M.P, Pew J, Nelson T.W, Li M, Comparison of formability of friction stir welded and laser welded dual phase 590 steel sheets, Sci Technol Weld Join. 2006; 11: 384-8.
[11] Ashrafi H, Shamanian M, Emadi R, Sarmadi M.A, Effect of welding parameters on the microstructure and tensile properties of friction stir-welded DP600 steel, SAE Int J Mater Manuf. 2019; 12: 165-78.
[12] Mahmoudiniya M, Kestens L.A.I, Microstructural development and texture evolution in the stir zone and thermomechanically affected zone of a ferrite-martensite steel friction stir weld, Mater Charact. 2021; 175: 111053.
[13] Ashrafi H, Shamanian M, Sanayei M, Farhadi F, Szpunar J.A, the impact of welding heat input on microstructure, micro-texture, and mechanical properties of stir zone in friction stir welded DP600 steel, Mater Today Commun. 2023; 37: 107127.
[14] Vences-Herna´ndez R, Reyes-Caldero´n F, Villalobos J.C, Vergara-Herna´ndez H.J, Salazar-Torres J.A, Evaluation of corrosion susceptibility of conventional dual-phase steels used in the automotive industry, J Mater Eng Perform. 2020; 29: 6520–34
[15] Abedini O, Behroozi M, Marashi P, Ranjbarnodeh E, Pouranvari M, Intercritical heat treatment temperature dependence of mechanical properties and corrosion resistance of dual phase steel, Mater Res. 2019; 22: 20170969.
[16] Beausir B, Fundenberger J.J, Analysis Tools for Electron and X-ray diffraction, ATEX-software, www. atex-software.eu, Universite´ de Lorraine - Metz. (2017).
[17] Wang Y, Tomota Y, Ohmura T, Morooka S, Gong W, Harjo S, Real time observation of martensite transformation for a 0.4C low alloyed steel by neutron diffraction. Acta Mater. 2020; 184: 30-40.
[18] Li S, Guo C, Hao L, Kang Y, An Y, In-situ EBSD study of deformation behaviour of 600 MPa grade dual phase steel during uniaxial tensile tests. Mater Sci Eng A. 2019; 759: 624-32.
[19] Li Y, Song R, Jiang L, Zhao Z, Deformation response of 1200 MPa grade martensite-ferrite dual-phase steel under high strain rates, Mater Sci Eng A. 2019; 750: 40-4.
[20] Ashrafi H, Shamanian M, Emadi R, Saeidi N, Microstructure, tensile properties and work hardening behavior of GTA-welded dual-phase steels, J Mater Eng Perform. 2017; 26: 1414-23.
[21] Wu J, Wray P.J, Garcia C.I, Hua M, Deardo A.J, Image quality analysis: a new method of characterizing microstructures, ISIJ Int. 2005; 45: 254-62.
[22] Lin H.P, Chen D, Kuo J.C, Grain boundary evolution of cold rolled FePd alloy during recrystallization at disordering temperature, Materials. 2015; 8: 3254–67.
[23] Ghassemi-Armaki H, Maaß R, Bhat S.P, Sriram S, Greer J.R, Kumar K.S, Deformation response of ferrite and martensite in a dual-phase steel, Acta Mater. 2014; 62: 197-211.
[24] Calcagnotto M, Ponge D, Demir E, Raabe D, Orientation gradients and geometrically necessary dislocations in ultrafine grained dual-phase steels studied by 2D and 3D EBSD, Mater Sci Eng A. 2010; 527: 2738–46.
[25] Zaefferer S, Romano P, Friedel F, EBSD as a tool to identify and quantify bainite and ferrite in low-alloyed Al-TRIP steels, J Microsc. 2008; 230: 499–508.
[26] Phelan D, Dippenaar R, Widmanstätten ferrite plate formation in low-carbon steels, Metal Mater Trans A. 2004; 35: 3701-6.
[27] Wei L, Nelson T.W, Influence of heat input on post weld microstructure and mechanical properties of friction stir welded HSLA-65 steel, Mater Sci Eng A. 2012; 556: 51-9.
[28] Wang Z.F, Li P.H, Guan Y, Chen Q.F, Pu S.K, The corrosion resistance of ultra-low carbon bainitic steel, Corr Sci. 2009; 51: 954-61.
[29] Guo J, Yang S, Shang C, Wang Y, He X, Influence of carbon content and microstructure on corrosion behaviour of low alloy steels in a Cl containing environment, Corr Sci. 2008; 51: 242-51.
[30] Chen H, Lv Z, Lu L, Huang Y, Li X, Correlation of micro-galvanic corrosion behavior with corrosion rate in the initial corrosion process of dual phase steel, J Mater Res Technol. 2021; 15: 3310-20.
[31] Ghanem W.A, Hussein W.A, AbouShahba R.A, Morad M.M, The corrosion behavior of ferrite bainite dual phase steel in 3.5% NaCl solution, Middle East J Appl Sci. 2016; 6: 627-35.
[32] Guo Y.b, Li C, Liu Y.c, Yu L.m, Ma Z.q, Liu C.x, et al. Effect of microstructure variation on the corrosion behavior of high-strength low-alloy steel in 3.5wt% NaCl solution, Int J Miner Metall Mater. 2015; 22: 604-12.
