Comparison of Tribological Behavior of Deep Cryogenic Treated Hot Work Tool Steel at Room and High Temperature
نوع مقاله : مقاله پژوهشی
Carlson EA (1990) Cold Treating and Cryogenic Treatment of Steel in ASM Handbook, vol. 4 Heat Treating, ASM International, 10th Ed., Metals Park, OH, pp 203–206.
Preciado M, Bravo PM, Alegre JM (2006) Effect of low temperature tempering prior cryogenic treatment on carburized steels. J Mater Process Technol 176(1–3):41–44.
Mohan Lal D, Renganarayanan S, Kalanidhi A (2001) Cryogenic treatment to augment wear resistance of tool and die steels. Cryogenics 41(3):149–155.
Chandler H., Heat Treater's Guide: Practices and Procedures for Irons and Steels, ASM International, 1995.
M. Koneshlou, K. Meshinchi Asl, F. Khomamizadeh,” Effect of cryogenic treatment on microstructure, mechanical and wear behaviors of AISI H13 hot work tool steel” Cryogenics 51 (2011) 55–61.
A. Çiçek, F. Kara, T. Kivak, E. Ekici, “Evaluation of machinability of hardened and cryo-treated AISI H13 hot work tool steel with ceramic inserts” Int. Journal of Refractory Metals and Hard Materials 41 (2013) 461–469.
M. Péreza, C. Rodrígueza, F. J. Belzuncea,” The use of cryogenic thermal treatments to increase the fracture toughness of a hot work tool steel used to make forging dies” Procedia Materials Science 3 (2014) 604 – 609.
Behnam, Makarian, Kamran Amini and Hamid Ghayour “Effect of deep cryogenic treatment on hardness and wear behavior of DIN1.2344, Advanced processes in Materials, Vol. 7, Num. 2, 2017.
Kchaou, M., Elleuch, R., Y., Desplanques, X., Boidin, G., “Degallaix Failure mechanisms of H13 die on relation to the forging process – A case study of brass gas valves”, Engineering Failure Analysis, Vol. 17, N. 2, pp. 403-415, 2010.
M. Koneshlou, K. Meshinchi Asl, F. Khomamizadeh,” Effect of cryogenic treatment on microstructure, mechanical and wear behaviors of AISI H13 hot work tool steel” Cryogenics 51 (2011) 55–61.
Alexandru G, Ailincai C, Baciu (1990) Influence of cryogenic treatments on life of alloyed high speed steels. Mém Étud Sci Rev Métall 4:283–388.
Yun D, Xiaoping L, Hongshen X (1998) deep cryogenic treatment of high-speed steel and its mechanism. Heat Treat Met 3:55–59.
Vimal AJ, Bensley A, Lal DM, Srinivasan K (2008) Deep cryogenic treatment improves wear resistance of EN 31 steel. Mater Manuf Process 23(4):369–376.
Darwin JD, Mohan Lal D, Nagarajan G (2008) Optimization of cryogenic treatment to maximize the wear resistance of 18% Cr martensitic stainless steel by Taguchi method. J Mater Process Technol 195(1–3):241–247.
Y. Dong, X. Lin, and H.S. Xiao, "Cryogenic Treatment of High-Speed Steel and Its Mechanism", Heat Treatment of Metals, Vol. 25, pp. 55-59. 1998.
Bensely A, Prabhakaran A, Mohan Lal D, Nagarajan G (2005) Enhancing the wear resistance of case carburized steel (En 353) by cryogenic treatment. Cryogenics 45(12):747–754.
Simranpreet Singh Gill & Jagdev Singh & Rupinder Singh & Harpreet Singh” Metallurgical principles of cryogenically treated tool steels—a review on the current state of science”, Int J Adv Manuf Technol (2011) 54:59–82.
Das D, Dutta AK, Ray KK (2009) Optimization of the duration of cryogenic processing to maximize wear resistance of AISI D2 steel. Cryogenics 49:176–184.
J. Hemanth, Tribological behavior of cryogenically treated B4Cp/Al–12% Si composites. Wear 258, 1732–1744 (2005).
A. Çiçek, F. Kara, T. Kivak, E. Ekici, “Evaluation of machinability of hardened and cryo-treated AISI H13 hot work tool steel with ceramic inserts” Int. Journal of Refractory Metals and Hard Materials 41 (2013) 461–469.
Soundararajan V, Alagurmurthi N, Palaniradja K (2004) On the enhancement of wear resistance of hardened carbon tool steel (AISI 1095) with cryogenic quenching. Trans Mater Heat Treat 25 (5):531–535.
K. Kato, K. Adachi, Wear Mechanisms. Chapter 7 of Modern Tribology Handbook, Ed. B. Bhushan, CRC Press. Boca Raton, 2001.
G.A. Fontalvo, R. Humer, C. Mitterer, K. Sammt, I. Schemmel "Microstructural Aspects Determining the Adhesive Wear of Tool Steels", Wear, Vol. 260, No. 9-10, pp. 1028-1034, 2006.
)