@article { author = {Safari, M. and Joudaki, J.}, title = {Experimental Investigation of Resistance Spot Welding of Ultrathin IF Steel Sheets}, journal = {International Journal of Iron & Steel Society of Iran}, volume = {16}, number = {1}, pages = {51-57}, year = {2019}, publisher = {Iron & Steel Society of Iran}, issn = {2981-0388}, eissn = {2981-0396}, doi = {}, abstract = {Resistance Spot Welding (RSW) is a powerful tool for overlap joint of thin sheets. The welding procedure contributes to affecting the electrical, thermal and mechanical properties of the sheets. In this article, resistance spot welding of ultrathin IF steel sheets (0.67 mm thickness) have been studied. The IF steel sheets were welded by different welding currents (65, 70, 80, 90 and 100 A). The microstructure of the samples was observed using an optical microscope and the tensile test has been carried out to determine the joint strength and fracture mode. The microstructural observations showed that the grain size increase in the fusion zone by increasing the welding current and the heat-affected zone experienced recrystallization and small equiaxed grains were formed in the heat-affected zone. The base metal keeps its high hardness value from the work-hardening induced by the previous rolling process. Best joint strength was obtained at 80 A welding current (2600 N). The fracture mode changes from partial interfacial failure (at lower welding current) to the pullout with tearing of the sheets (at higher welding current).}, keywords = {Resistance Spot Welding Process؛ Joint strength,Failure Mode؛ IF steels}, title_fa = {بررسی تجربی جوشکاری نقطه ای مقاومتی ورقهای بسیار نازک فولاد IF}, abstract_fa = {جوشکاری نقطه ای مقاومتی ابزاری قدرتمند برای اتصال ورق های نازک است. روش جوشکاری به خصوصیات الکتریکی ، حرارتی و مکانیکی ورق ها کمک می کند. در این مقاله ، جوشکاری نقطه ای مقاومتی ورق های فولادی بسیار نازک فولاد IF (ضخامت 0.67 میلی متر) مورد بررسی قرار می گیرد. ورق های فولادی IF توسط جریان جوشکاری مختلف (65 ، 70 ، 80 ، 90 و 100 A) جوش داده می شوند. ریزساختار نمونه ها توسط میکروسکوپ نوری مشاهده می شود و آزمایش کششی برای تعیین استحکام اتصال و مود شکست انجام شده است. مشاهدات ریزساختاری نشان می دهد که با افزایش جریان جوش ، اندازه دکمه جوش در منطقه جوش افزایش می یابد و منطقه تحت تأثیر گرما دوباره تبلور مجدد را تجربه می کند و دانه های مخلوط کوچک در منطقه تحت تأثیر گرما شکل می گیرد. فلز پایه مقدار سختی بالا را از سخت شدن کار ناشی از فرآیند نورد قبلی حفظ می کند. بهترین مقاومت مفصل در جریان جوشکاری 80 A (2600 N) بدست می آید. مود شکست از حالت فصل مشترکی جزئی (در جریان جوشکاری کمتر) به حالت محیطی (در جریان جوشکاری بالاتر) تغییر می یابد.}, keywords_fa = {جوشکاری نقطه ای مقاومتی,استحکام اتصال,مود شکست,فولادهای IF}, url = {https://journal.issiran.com/article_36842.html}, eprint = {https://journal.issiran.com/article_36842_e3ea57888304be186256971bfe369a78.pdf} }