@article { author = {Rabani, M. and Zandrahimi, M. and Ebrahimifar, H.}, title = {High Temperature Oxidation Behavior of Aluminide Coating Fabricated on UNS S30815 Stainless Steel}, journal = {International Journal of Iron & Steel Society of Iran}, volume = {16}, number = {1}, pages = {41-50}, year = {2019}, publisher = {Iron & Steel Society of Iran}, issn = {2981-0388}, eissn = {2981-0396}, doi = {}, abstract = {Aluminide coatings are widely used as a protective coating material due to their high corrosion and oxidation resistance properties. In this research, an aluminide coating was fabricated through aluminizing on UNS S30815 austenitic stainless steel using pack cementation method at 950 °C for 5 h. The isothermal oxidation was exerted on uncoated and aluminide coated steels for 200 h at 1050 ºC. Also cyclic oxidation was applied for 50 cycles at 1050 ºC on coated and uncoated steels. Surface morphology and cross section of coated and oxidized samples were characterized by means of scanning electron microscopy (SEM) and energy dispersive X-ray spectrometry (EDS). X-Ray diffraction (XRD) was used to identify the formed phases in the surface layer of as-coated and oxidized specimens. As-coated UNS S30815 consisted of Al5Fe2, FeAl3 and Al2O3 phases. The results of the isothermal oxidation showed that the coated steel had lower weight gain (2.9 mg.cm-2) after 200 h of oxidation in comparison with uncoated one (7 mg.cm-2). Also the results of cyclic oxidation showed that the coated specimens had good resistance to thermal cycles.}, keywords = {UNS S30815 austenitic stainless steel,Aluminizing,pack cementation,Oxidation}, title_fa = {High Temperature Oxidation Behavior of Aluminide Coating Fabricated on UNS S30815 Stainless Steel}, abstract_fa = {پوشش های آلومینید به دلیل داشتن خاصیت خوردگی بالا و مقاومت در برابر اکسیداسیون ، به عنوان ماده پوشش محافظ بسیار مورد استفاده قرار می گیرند. در این تحقیق، پوشش آلومینید از طریق آلومینایزینگ کردن روی فولاد ضد زنگ آستنیتی UNS S30815 با استفاده از روش سمانتاسیون فشرده در ℃ 950 به مدت 5 ساعت ساخته شد. اکسیداسیون همدما بر روی فولاد بدون پوشش و فولاد آلومینایزشده به مدت 200 ساعت در دمای 1050 درجه سانتیگراد اعمال شد. همچنین اکسیداسیون سیکلی برای 50 سیکل در دمای 1050 درجه سانتیگراد روی فولاد پوشش دار و بدون پوشش اعمال شد. مورفولوژی سطح و سطح مقطع نمونه های پوشش داده شده و اکسیده شده با استفاده از میکروسکوپ الکترونی روبشی (SEM) و طیف سنجی پراش اشعه ایکس (EDS) مشخصه یابی شد. از پراش پرتو ایکس (XRD) برای شناسایی فازهای تشکیل شده در لایه سطحی نمونه های پوشش دار و اکسیده شده استفاده شد. فولاد UNS S30815 پوشش داده شده شامل فازهای Al5Fe2، FeAl3 و Al2O3 بود. نتایج اکسیداسیون همدما نشان داد که فولاد پوشش داده شده (mg.cm-2 9/2) پس از 200 ساعت اکسیداسیون در مقایسه با نمونه بدون پوشش ( mg.cm-27) افزایش وزن کمتری داشت. همچنین نتایج اکسیداسیون سیکلی نشان داد که نمونه های پوشش دار مقاومت خوبی درسیکل های حرارتی دارند.}, keywords_fa = {فولاد زنگ نزن آستنیتی UNS S30815,الومینایزینگ,سمانتاسیون فشرده,اکسیداسیون}, url = {https://journal.issiran.com/article_36841.html}, eprint = {https://journal.issiran.com/article_36841_464e15f5566baa892bbd43beb2e7f934.pdf} }